for the FM-1
on the SMK-37
For the M-Vave SMK-37 Pro, the Donner Starrykey 37 Play (the same keyboard), the SMK-37 Elite and the MKE-P37. Tested on a Donner Starrykey 37 Play; the Elite and MKE-P37 builds have not been tried on a keyboard yet.
What you get
The same SQ-80 as on the FM-1, on a keyboard with more to hold on to: 37 keys with velocity, 16 pads, four faders, pitch and mod wheels and a sustain pedal jack.
- Two banks of 40 programs, yours: load ESQ-1 / SQ-80 banks into them and save your programs there. No banks yet? Thousands are at Rainer Buchty's Ensoniq archive, in the Ensoniq sounds 2022-07 collection and in Don Solaris's collection.
- Your ROM pack (the SQ-80's original waves, from your own ROM dumps) goes in over the keyboard's stock presets; without one, SQ-80 plays its own 75 waves.
Install
Connect the keyboard by USB (switched on, as it is), open the installer for your model in Chrome or Edge and press Install. Nothing to download or set up.
It asks for your ROM pack and up to two banks (they go to banks 1 and 2), or installs the firmware alone. You can load them later with the Load page; the ROM pack maker makes the pack from your SQ-80's ROM dumps.
Updates: the same installer, the same way. Version 0.14.0; the packages: Pro · Elite · MKE-P37.
Optional: a full backup first
SQ-80 never writes the keyboard's own calibration or Bluetooth data, and leaves the stock firmware's data alone except its presets, which the ROM pack replaces. If you want a copy of everything before the first install, read the whole flash on a Windows computer (about ten minutes, once):
- Install Python 3.12 from python.org ("Windows installer (64-bit)"; tick Add python.exe to PATH; not 3.13 or newer).
- Download and unzip into Downloads: the SQ-80 folder and jl-uboot-tool; and the package for your model (above) into Downloads.
- Connect the keyboard, close every program that uses MIDI, and double-click
smk37-backup.batin the SQ-80 folder (allow it as administrator). It ends with backup OK. - Copy the
backupfolder it made to a USB stick. Never share those files: they are your unit's. Switch the keyboard off and on, then install as above.
Linux, by hand: docs/SMK37-BACKUP.md.
The controls
| K1 | Volume |
| K2 · K3 · K4 | Bank (1, 2) · the section's page · program |
| K5–K8 | The four values of the page (on the play screen: cutoff, resonance, attack, release). Where the screen says K1–K4, it means these. |
| Keys | All 37 play, with their velocity. OCTAVE − / + move them. |
| Pads | The bank's programs, 16 at a time (< >: the next 16). With SEQ held: the 16 steps. |
| < > | Elsewhere: the section's pages back and forward. |
| Faders | FADER BANK steps A–D (shown on the screen). A: reverb, delay, chorus, drive. B: cutoff, resonance, attack, release. C: the three oscillators' levels and the volume. D: LFO 1 and 2, rate and depth. A fader takes over a value once it reaches it: until then the screen says UP TO or DOWN TO. |
| Wheels · pedal | Pitch bend · the SQ-80's WHEEL source · sustain. |
| Buttons | As on the FM-1: SCALE = SEL, CHORD = ENV, NOTE REPEAT = LFO, PARA = EDIT, FX, GLOBE = GLO, PATCH = HOME, BT = SAVE, ARP, SEQ, SEQ PLAY = PLAY, SEQ REC = REC. |
The rest works as the manual says for the FM-1.
Back to M-Vave's firmware
Install it with M-Vave's updater, as for any update. The calibration and Bluetooth data were never touched. The stock presets SQ-80's ROM pack replaced are in your backup, if you made one.
The SMK-37 support builds on genkigenki's fm1-to-smk37 kit and SMK-37 layer (GPL-3.0); the optional backup reads the flash with kagaimiq's jl-uboot-tool.